Announcement

Store is currently OPEN check out the SPECIAL OFFERS page for some great BARGAINS from Team PRC

Show: 

Result Pages:
Baja Bleeder Shock Cap (2) Silver by TFE

Team FastEddy Bleeder Cap System for the HPI Baja 5B & 5T (Compatible with HPI VVC & RTR Shock Tubes) The absolute easiest and most accurate way to properly bleed your shocks. Bleeding your shocks just became as easy as 1-2-3 Fill the shock with the fluid of your choice. Screw the bleeder cap on. Slowly push the shock shaft up until it is fully compressed, insert and tighten the bleeder screw. FastEddy done away with the stock swivel ball and have included a rubber bushing with…

Manufacturer
Team Fast Eddy
Model
tr270
Baja SS Header Exhaust Clamp Alloy fit Tuned Pipe by TeamFastEdd

TFE Alloy heavy-duty clamp for HPI SS Tuned pipe.  Replace your  stock Clamp

TFE clamp is built to last,  solid fit & easy to install.  Will fit HPI Baja  SS, 5T SC with SS exhaust pipe

Manufacturer
Team Fast Eddy
Model
fd164
Quantity
9
Baja Steering Post Shims by Teamfasteddy Shim Kit


This kit contains 6 shims designed specifically for the HPI Baja 5B and 5T to eliminate the slop that exists in all the stock units from the factory. Installing the shims will not only make your Baja more responsive but will also prolong the life of the bearing. If your serious about your Baja this is a must have product …

Manufacturer
Team Fast Eddy
Model
steeringpost
Quantity
3
Bearing Retainer Compound by Team FastEddy

2 ml Reusable Pen. Green Retaining compound. Retaining compound is used when press or slip fitting cylindrical components that are not threaded. It fills the gaps between parts, creating a rock solid connection. This is an all purpose, quick curing compound that is perfect for general press fit applications for gaps up to .005" that will not be exposed to excessive heat. Perfect for holding the bearings on the metal diff housing of the HPI Baja, Wheel Bearings on a metal hub and several other places on…

Manufacturer
Team Fast Eddy
Model
tt458
Quantity
9
Clutch Bearing Set  for Losi 5ive T by Team FastEddy

Replacement Clutch Bearing Set for the Losi 5ive-T…

Manufacturer
Team Fast Eddy
Model
losi5clutchb
Quantity
4
Clutch Bearings fit Turtle Racing Clutch by TFE

Team FastEddy Replacement Clutch Bearing Set for Turtle Racing Clutch System. This is a set of two (2) bearings.   Will fit Turtle Racing Clutch System Only          …

Manufacturer
Team Fast Eddy
Model
gt279
Quantity
1
Clutch Shims Losi 5ive T 15mm & TR Clutch Baja by Team FastEddy

Shimming your clutch bell properly is an important part of properly servicing and maintaining your RC. To much play can cause undue heat and alignment issues resulting in premature bearing failure.
This kit contains 4 shims. 2 x  .1 2 x  .3
With these units you can mix and match them for the perfect fit. Combinations will get you the following thicknesses:
.1,.2,.3,.4,.5,.6,.7,.8mm Perfect for any clutch system needs. For use with ALL Losi 5ive clutch bells…

Manufacturer
Team Fast Eddy
Model
sm235
Hinge Pin Shims 0.2mm by TeamfastEddy

Team FastEddy Thin Hinge Pin Shims Properly shimmed hinge pins are a must for anyone driving an HPI Baja. There is excessive play in all the Baja hinge pins. This allows the pin to slam back and forth and damage the c-clips. This is the leading cause of the c-clip getting damaged and falling off. Properly installing shims will reduce this issue to close to zero. There in many cases…

Manufacturer
Team Fast Eddy
Model
hingpos.2mm
Quantity
2
Result Pages: