Announcement
DDM
DDM G320RC Zenoah v2 Insulator Block Billet & Teflon Gaskets AV9
Billet Aluminum Zenoah G320RC / G320PUM Insulator Manifold Block with PTFE heat spacer gaskets for both cylinder and carburetor side. This is the v2 version of the manifold, this version is the exact same thickness (spacers included) as the stock manifold setup, so no adjustment is required in R/C throttle linkage setups. Fits Zenoah G320RC / G320PUM engine only. Does NOT fit earlier Zenoah RC models! replacement for Zenoah part # 585727001, won't warp in high heat. Made in the USA of 6061 billet aluminum.…
- Manufacturer
- DDM
- Model
- av981
- Quantity
- 1
.jpg "DDM HD Shock Springs 11.00lb. Rate Rear for Losi 5iveTBlack")
DDM HD Shock Springs 11.00lb. Rate Rear for Losi 5iveTBlack
DDM HD Shock Springs 11.00lb. Rate for Losi 5iveT Rear Black …
- Manufacturer
- DDM
- Model
- sp4301
- Quantity
- 1
DDM HD Shock Springs 14.5lb. Rate Front for Losi 5iveT Black
DDM HD Shock Springs 14.5lb. Rate Front for Losi 5iveT Black …
- Manufacturer
- DDM
- Model
- sp430 : sp430c
- Quantity
- 1
DDM Silencer for 1/5 RC Exhaust Pipes Chrome
DDM Dominator® brand pipe silencer.Mounts to most tuned pipes with 5/8" bleed to reduce noise. Includes silencer, heavy-duty mounting tube, and clamps
Will work with pipes: ADA S1, ADA S2, Engine Trix, Sikk Torque Pipe, Sikk M1 Pipe, PPS Pipe, Flowsystem Pipe, PacSales S25 Pipe, DDM Dominator for HPI and FG vehicles. Also fits Proline Racing 'rattlesnake' pipes when mounted to the 5/8" rattlesnake 'stinger'.
The length of the silencer body is 4.25" (108mm), and the width is 1.5" (38mm)
…
- Manufacturer
- DDM
- Model
- fd782
- Quantity
- 1
Easy Grip Body Clips YELLOW by DDM
Now available "Easy Grip" body clips! Sold in sets of ten (10) Ever found it annoying to pull off the stock clips? This problem is solved! Not only do these "easy grip" clips look great, they work great too. No more fussing over body clips!…
- Manufacturer
- DDM
- Model
- ee888
- Quantity
- 1
Exhaust Tube (2)Hi Temp Silicone Black 150mm lg Silencer
High temp reinforced Silicone tube. 13mm (1/2") inner diameter, 19mm (3/4") outer diameter. Inner reinforcing fibers for extreme durability. Includes two (2) 150mm (6") pieces of tubing. Use this on your Exhaust to route exhaust away from your vehicle…
- Manufacturer
- DDM
- Model
- fd818
- Quantity
- 1
Lipo Battery 7000mAh 7.4v RX Pack DDM fit Losi5T B WRC Vekta XCR
7000mAh 7.4v LiPo Receiver battery pack. Lipo Receiver Battery more run time less weight . DDM Racing 7000 mAh LiPo receiver battery for the Kraken VEKTA, Losi 5IVE-T/Mini WRC, TLR 5IVE-B and RCMK XCR line of cars. Increase your run time over the original batteries with power to last. Features flexible 22 awg wire with a JR style servo connector and an XH type balance plug. There are two leads, one made to plug into your on/off switch and another for charging. 101mm…
- Manufacturer
- DDM
- Model
- bt285
- Quantity
- 1
![Losi 5ive "Pro" Throttle Linkage for Reed Case Motors by DDM](images/thumbs/510_510/ht275.jpg "Losi 5ive "Pro" Throttle Linkage for Reed Case Motors by DDM")
Losi 5ive "Pro" Throttle Linkage for Reed Case Motors by DDM
The DDM "Pro" Throttle linkage is a simple install to replace your existing throttle linkage on your Losi 5IVE. This version fits the REED CASE motors. With the new Pro quick release linkage it makes removing your motor significantly easier. Featuring a precision machined aluminum locking sleeve, this linkage will hold tight and give you the precise throttle control you need. Installs in minutes! DO NOT OVER TIGHTEN THE BALL JOINT ON THE CARB LINKAGE ARM, THEY WILL BREAK. Your engine…
- Manufacturer
- DDM
- Model
- ht273 REED
- Quantity
- 1
Losi 5T Pro Throttle Linkage Losi 5ive T by DDM
"Pro" Throttle linkage is a simple install to replace your existing throttle linkage on your Losi 5IVE. With the new Pro quick release linkage it makes removing your motor significantly easier. Featuring a precision machined aluminum locking sleeve, this linkage will hold tight and give you the precise throttle control you need. Installs in minutes.
*Your engine cover will require slight trimming to allow for clearance of the locking sleeve connector
*DO…
- Manufacturer
- DDM
- Model
- ht275
- Quantity
- 1
Victory RC Exhaust Replacement Sandwich Mount M6
Thread M6 Compression Capacity per Mount 50 lbs. Deflection @ Maximum Capacity 0.06" Shear Capacity per Mount 15 lbs. Deflection @ Maximum Capacity 0.10" Height (A) 3/4" Width (B) 1" Thread Length (C) 1/2" Depth (D) 3/16" Additional Specifications Style 2—Male Threaded Stud on One End; Female Threaded Insert on One End Neoprene Metric Steel Stud and Insert RoHS Compliant Diminish vibration, shock, and noise in compression and shear load applications. Mounts have two threaded studs and/or inserts that are sandwiched between black natural rubber or neoprene. Durometer is 50A, unless noted. Neoprene has good resistance to weather and acids; moderate resistance to oils. Temperature range is 10° to 180° F…
- Manufacturer
- DDM
- Model
- fd217b
- Quantity
- 1
