Displaying 1 to 10 (of 77 products)
5mm Replacement Dowel-Pins for PhatDad Cross-Over Dogbones and Drive Cups and other 5mm drives
8 x M5x22 Dowel Pins
2x M5x24 Dowel P5mm Replacement Dowel-Pins for PhatDad Cross-Over Dogbones and Drive Cups.
8 x 10/32 Thread Screw…
- Manufacturer
- DDM
- Model
- tt366b
Now available DDM Racing new DDM Bite-Lock rings. Made from durable fiberglass reinforced nylon with a deep lip that allows for optimum sidewall protection from getting pinched or torn. The inside of the ring features a large groove to easily fit the tire flange and bite down to keep the tire in place. Moulded into the ring is the DDM Racing logo for a touch of style. Compatible…
- Manufacturer
- DDM
- Model
- ddm100ngn
This gear set is desiged for use with the 5B 5T SC Standard or Upgraded Alloy Clutch system
Innovative design eliminates need for the spur gear carrier. This set includes an 18T pinion gear and 56T spur gear for a big increase in top speed. Gears are heat treated, then finished off with a smooth black chromate coating.
Spur Gear Specifications:
Material - 1141 Steel
Heat Treat - Induction hardened teeth .010-.020…
- Manufacturer
- DDM
- Model
- gg804
Now available "Easy Grip" body clips!
Sold in sets of ten (10)
Ever found it annoying to pull off the stock clips? This problem is solved! Not only do these "easy grip" clips look great, they work great too. No more fussing over body clips!…
- Manufacturer
- DDM
- Model
- ee889
Now available "Easy Grip" body clips!
Sold in sets of ten (10)
Ever found it annoying to pull off the stock clips? This problem is solved! Not only do these "easy grip" clips look great, they work great too. No more fussing over body clips!…
- Manufacturer
- DDM
- Model
- ee889black/c
7000mAh 7.4v LiPo Receiver battery pack.
Lipo Receiver Battery more run time less weight .
DDM Racing 7000 mAh LiPo receiver battery for the Kraken VEKTA, Losi 5IVE-T/Mini WRC, TLR 5IVE-B and RCMK XCR line of cars. Increase your run time over the original batteries with power to last. Features flexible 22 awg wire with a JR style servo connector and an XH type balance plug. There are two leads, one made to plug into your on/off switch and another for charging.
101mm…
- Manufacturer
- DDM
- Model
- bt285
"Pro" Throttle linkage is a simple install to replace your existing throttle linkage on your Losi 5IVE. With the new Pro quick release linkage it makes removing your motor significantly easier. Featuring a precision machined aluminum locking sleeve, this linkage will hold tight and give you the precise throttle control you need. Installs in minutes.
*Your engine cover will require slight trimming to allow for clearance of the locking sleeve connector
*DO…
- Manufacturer
- DDM
- Model
- ht275
High-performance silicone exhaust tubing. 13mm (1/2") inner diameter, 19mm (3/4") outer diameter. 450mm of tubing Inner reinforcing fibers for extreme durability. Allow you to route your exhaust freely. Also provides SIGNIFICANT noise reduction when connected to stock mufflers or tuned pipes. Can be trimmed to any desired length - significant noise reduction can be achieved using only a few inches of tubing.
13mm ID 19mm OD
Wall 3.5mm
2 Ply.…
- Manufacturer
- DDM
- Model
- fd108 45cm no clamp
"Black Magic" HARDENED STEEL Heavy Duty Drive Gear 19 Tooth for HPI Baja 5T/5SC
This is the size used in the HPI Baja 5T/5SC
Specifications: Material - 1141 Steel Heat Treat - Induction hardened Finish - Black Chromate . Same as HPI # 86483, just made in USA of premium steel, and heat treated for maximum strength and hardness. Get the best... Get BLACK MAGIC! All DDM "Black Magic" gears are made in the USA.…
- Manufacturer
- DDM
- Model
- 86483s
- Quantity
- 1
Billet Gas Cap Bio Hazard Black
Will fit: Losi 5ive DBXL , HPI Baja 5B, SS 5T SC
Does Not Come with Rubber seals…
- Manufacturer
- DDM
- Model
- jj470bk
- Quantity
- 1
Displaying 1 to 10 (of 77 products)